Most of the media converter questions that reach our support desk are not about datasheets. They are about the four things that decide whether a link actually comes up: what the hardware does with the frame, what the panel markings mean, which fibre is already in the ground, and what to check first when the link LED stays dark. The answers below come from our test bench and from field reports on the commercial and industrial ranges we build. Every ethernet to fiber media converter in the range is listed by model on the media converter product line page.
What is a media converter and how does it work?
A media converter has two ports on two different physical media — almost always RJ45 copper on one side and fibre on the other — and moves Ethernet frames between them. Nothing is routed, filtered or rewritten on the way through: the copper PHY recovers the bit stream, the logic re-times it, and the optical transceiver drives it onto the fibre at the same line rate. Because the frame arrives at the far end unchanged, the two end devices behave as if they were joined by one continuous cable. That is what transparent means on a converter datasheet, and it is why converters are described as point-to-point bridges rather than switches.
Transparency has limits, and they are worth knowing before you buy. A converter cannot join two different speeds — a 10/100 unit will not bring up a gigabit link, whatever the copper side negotiates. It passes VLAN-tagged frames through untouched but does not add, strip or interpret tags. It has no routing, no firewall and no spanning tree. Where any of those are required, a switch with SFP slots is the right part.
What do FX, FDX, TX and RX mean on a media converter?
The panel uses two naming systems at once, which is where the confusion starts. TX and RX describe direction; TX and FX also describe port type. On a converter body, TX printed beside the RJ45 socket means the copper port (the name comes from 10/100BASE-TX), and FX beside the optical socket means the fibre port (from 100BASE-FX). On an SFP label, or on the fibre pair itself, the same two letters mean transmit and receive instead.
FDX is not a port. It is the duplex status LED: lit when the port has negotiated full duplex, dark when it has fallen back to half duplex. That reading only means something on a 100M link. At gigabit the LED stays lit permanently, because 1000BASE-X has no half-duplex mode — if you are chasing a duplex problem on a gigabit converter, look at the switch counters, not at FDX.
Marking | Where it is printed | What it tells you |
TX | beside the RJ45 socket | copper port (10/100BASE-TX) |
FX | beside the optical socket | fibre port |
TX / RX | SFP labels, fibre pair labels | transmit / receive direction |
FDX | status LED | full duplex negotiated; always on at 1G |
SPD | status LED | negotiated speed (100 or 1000) |
LNK / ACT | status LED | link up / traffic present |
Do media converters have MAC addresses?
The unmanaged converters in our range do not, and the reason is architectural. They work at the physical layer: the frame is recovered, re-timed and re-transmitted, and is never examined at layer 2. With no layer-2 stack there is no MAC address to assign, nothing that appears in a switch MAC table, and nothing that shows up in a traceroute. The MAC addresses visible at each end belong to the two end devices, not to the box in the middle.
Two practical consequences follow. Port security, MAC filtering and MAC-based VLAN assignment cannot be applied to a converter — those controls have to sit on the switch port behind it. And a chassis that carries an SNMP agent is the only exception: it holds a MAC address for its management interface, but that address never forwards customer traffic.
Single-mode or multimode: which media converter do I need?
The fibre already in the ground decides this, not the converter. Single-mode (9/125 µm) runs with 1310 nm or 1550 nm optics and covers 10 km to 80 km. Multimode (50/125 µm OM3/OM4, or legacy 62.5/125 µm OM1) runs with 850 nm optics and is normally limited to a few hundred metres inside a building or between cabinets. The two are not interchangeable: different core geometry, different wavelength, different optics.
The fault we see most often is a pair that is right at one end and wrong at the other — an 850 nm multimode unit facing a 1310 nm single-mode unit across a single-mode run. It sometimes links over a very short distance with heavy loss, which reads like an intermittent fault rather than a mismatch. Read both labels before you test anything else.
Multimode | Single-mode | |
Fibre core | 50/125 µm (OM3/OM4), 62.5/125 µm (OM1) | 9/125 µm |
Wavelength | 850 nm | 1310 nm / 1550 nm |
Typical reach | a few hundred metres | 10 km to 80 km |
Where it fits | in-building, cabinet to cabinet | campus, street, long runs |
Cost profile | cheaper optics | higher optic cost, far lower loss |
Fixed optical port or SFP cage: which media converter fits my link?
What you are choosing is not a converter or a module — it is the optical port on the converter: a fixed 1×9 port, or an empty SFP cage. If the reach and wavelength are already fixed in your bill of materials, take the fixed port; if either may change, take the cage. The phrase “media converter vs SFP module” compares two different kinds of object: an SFP module is a component with no RJ45 port, no power input and no enclosure of its own, while a converter is a box you mount and power.
Fixed 1×9 optical port | SFP cage | |
What sits on the board | optical module fixed at build time, SC connector by default (FC/ST on request) | empty slot to SFP MSA, module ordered separately |
Wavelength and reach | fixed at order: 850 nm multimode, 1310/1550 nm single-mode, BiDi pairs, 550 m to 120 km | decided on site by the module you plug in |
If the optic fails, or the reach changes | replace the whole converter — the link stays down until a spare unit arrives | swap the module — link back up, or re-graded from 20 km to 80 km, with one part |
Spare parts to hold | one complete unit per model, so stock multiplies with every model deployed | one module per wavelength, covering every unit that uses it |
Unit price sits in the same class either way: the optic is paid for once, whether it is built into the unit or bought as a module. Price is therefore a poor tie-breaker. What really differs is what happens after a failure, and how much stock you have to carry to survive one.
Three rules settle it in practice:
- Reach and wavelength are frozen in the BOM — the fixed-port 1000M unit has nothing that can be configured wrong, and no separate module to source. Most of our 100M and 1000M volume still ships with a fixed SC port for exactly that reason.
- The site is not surveyed yet, or the reach may change — take the cage. Plug the module when the fibre is known, not when the converter is ordered. Our 2.5G and 10G units ship with a cage as standard, because 2500BASE-X and 10G optics are not built as fixed 1×9 parts.
- Spares are stocked centrally across several sites — the cage wins on inventory: one module per wavelength instead of one converter per model, and a failed optic is a module swap rather than a whole-unit replacement.
Two optical ports follow the same logic. For 1+1 protection you want a dual-SFP unit; for single-mode to multimode relay, an SFP-to-SFP mode converter, since neither job can be done with a single fixed port.
There is only one case where modules genuinely replace the converter: both ends already have a switch with a free SFP slot. Then fit a module at each end and skip the box — no power supply, one less device to fail. Converters come back at the copper edge, where a PLC, camera or industrial PC offers nothing but RJ45, or where the copper side needs PoE that no module can inject. SFP module questions themselves — coding, rated reach, mixing single-mode modules with multimode cable — are answered in the SFP module FAQ.
Is the power adapter included with the fiber media converter?
It depends on the product series. For our Commercial Grade media converters, a standard external power adapter is included in the package. However, for Industrial Grade models, the power supply is not included by default and must be purchased separately based on your specific voltage and mounting requirements.
On the 1000M PoE model the bundled adapter is rated 24 W (100–240 VAC in, 48 VDC 0.5 A out). If the powered device draws close to the full 30 W PoE budget, tell us at the order stage and we will quote a larger adapter instead.
Can these fiber media converters be mounted in a rack?
Most of our standalone media converters are compatible with our 14-slot media converter chassis, except for the 4-port models. Please note that we do not recommend using third-party media converters in our chassis (or vice versa), as dimensions and power connector positions vary between brands.
Are your fiber media converters compatible with other switch brands?
Generally, yes. Fiber media converters operate as point-to-point transparent transmission devices. As long as the following technical specifications match on both ends of the link, they are “Plug and Play” and can interconnect with any managed or unmanaged switch brand:
- Speed: Both ends must support the same rate (e.g., 10/100M or 1000M).
- Fiber Type: Both devices must use the same type of fiber (Single-mode or Multi-mode).
- Wavelength: The transmission and reception wavelengths must be consistent (e.g., 1310nm on both sides, or matched TX1310/RX1550nm and TX1550/RX1310nm for BiDi models).
- Distance: The fiber length should be within the rated transmission distance of the devices (e.g., 20km).
Will the LFP (Link Fault Pass-through) function work with other brands?
We strongly recommend using our ethernet to fiber media converters on both ends if you require LFP. While basic data transmission is compatible, the LFP signaling logic often differs between manufacturers. If used with a different brand, the LFP function may not trigger correctly.
How do the LED indicators behave when LFP is enabled?
LFP ensures that if one side of the link fails, the other side is forced down to alert the system. For example, if the Ethernet (Copper) link fails, the Fiber port will automatically shut down. In this scenario, both the Copper port LED and the Fiber port LED will remain OFF, indicating a link failure across the entire path.
Can the fiber optic media converter operate stably in an outdoor cabinet at -20°C?
While our Commercial Grade units support an operating temperature of -20°C to 65°C, for outdoor monitoring boxes or extreme environments, we highly recommend our industrial media converter series. They are designed for harsher conditions with a wider temperature range of -40°C to +85°C and better heat dissipation.
Those figures are typical for each grade, not a single guarantee across every variant. Three examples from the current range: the 1000M PoE model AOM-2100DP is rated -20°C to 60°C, the 2.5G AOM-4100 -10°C to 60°C, and the 10G AOM-5100 -10°C to 55°C. Ratings move with speed, power option and enclosure, so confirm the exact model against its datasheet before you write the number into a specification.
The two ranges differ on more than temperature alone:
Spec | Commercial Grade | Industrial Grade |
Operating temperature | -20 °C to 65 °C | -40 °C to +85 °C |
Typical deployment | Office, data center, indoor cabinet | Outdoor monitoring box, factory floor, roadside cabinet |
Mounting | Standalone, or 14-slot rack chassis¹ | DIN-rail |
Power supply | External adapter included | External industrial power supply, sold separately (e.g. HDR-15-24) |
Warranty | 3 years | 5 years |
¹ 14-slot chassis compatibility applies to standalone models except the 4-port units.
AOA Media Converter Selection: Commercial grade (Indoor) vs. Industrial grade (Outdoor/Rugged) operating environment comparison.
Are AOA Technology media converters CE, FCC and RoHS compliant?
Yes. CE, FCC and RoHS are held per model family, not claimed for the whole range as a block.
Mark | What is held |
CE | EMC and product safety, self-declared, with the test reports behind the declaration |
FCC | Part 15 Subpart B, Class A limits |
RoHS | Restricted substances, ten items |
Name the model you are specifying and the certificates for that model go out as PDF with the quotation — the paperwork a compliance file needs, not a logo on a datasheet.
What is the warranty period for AOA Technology Ethernet media converters?
Warranty runs by grade:
- Commercial Grade media converters: 3 years.
- Industrial Grade media converters: 5 years.
The full terms, including what is excluded, are on the warranty policy page. If a tender asks for a longer term, raise it at quotation stage — that is a commercial decision, not something a datasheet can answer.
What types of media converters does AOA Technology offer?
The range is easiest to read four ways: by environment, by speed, by port configuration, and by form factor.
In short: Commercial Grade for climate-controlled rooms, Industrial Grade for -40°C to +85°C DIN-rail sites, speeds running from 10/100M through Gigabit and 2.5G up to 10G, and multi-port, PoE, LFP, redundant-fibre and mini variants inside those families.
By application environment
Commercial Grade: Designed for climate-controlled environments like offices and data centers, featuring external AC or DC power adapters.
Industrial Grade: These industrial media converter models are built for extreme conditions, with a wide operating temperature range of -40°C to +85°C. They are typically DIN-rail mounted and require an external industrial power supply (e.g., HDR-15-24).
By transmission speed
Fast Ethernet (10/100Mbps): 10/100 copper to 100BASE-FX, standalone.
Gigabit Ethernet (10/100/1000Mbps): 10/100/1000 copper to 1000BASE-X, auto-sensing and Jumbo frame support, standalone or mini.
2.5G Media Converters: 2.5GBASE-T copper to a 2500BASE-X SFP cage, for Wi-Fi 6/7 access points and NAS uplinks that have outgrown 1G but do not justify 10G yet.
10G Media Converter: 10G/5G/2.5G/1G copper to a 10GBASE-X SFP+ cage, for 10G backbone links between switches.
By port configuration & special features
Multi-Port Converters: We offer units with 2-TX or 4-TX Ethernet ports, allowing multiple copper devices to connect to a single fiber link.
PoE Media Converter: feeds IP cameras or wireless APs over the same copper cable that carries their data, per IEEE 802.3af / 802.3at, with a 30 W PoE budget at the copper port. If you have seen 24 W or 65 W quoted against a PoE model, that is the rating of the external adapter we supply — not a PoE class.
LFP Support: Models equipped with a DIP Switch to enable Link Fault Pass-through (LFP) for synchronized link failure detection.
Specialized Models: Including 1+1 Redundant Fiber converters for high-reliability links and SFP-to-SFP Mode Converters.
LED Display Transmission System: A dedicated 1000Mbps system specifically engineered for high-quality LED screen signal transmission.
By form factors
Mini Type: Compact designs for individual deployment or high-density placement.
Standalone/Rack-Mountable: Standard standalone units (1-TX and 2-TX ports) can be integrated into our 14-slot Media Converter Rack with redundant AC or DC power supplies.
How do I connect a media converter and confirm the link is up?
Work through it in this order, and you will clear the four faults behind most dead-link calls before you open a ticket.
- Power and speed. PWR lit, and SPD matching the device at the far end.
- Fibre polarity. Swap TX and RX at one end. On BiDi single-fibre pairs, confirm the two units are opposite wavelength pairs — TX1310/RX1550 facing TX1550/RX1310. Two identical units will never link.
- Connector end-faces. Contamination is the most common reason a link that worked yesterday is dark today. Clean both ends before you change any hardware.
- The copper side. LNK on the RJ45, cable category, and whether one end is auto-negotiating while the other is forced.
Symptom | Check first |
PWR dark | supply, adapter rating, DC polarity |
Fibre LNK dark, copper LNK lit | polarity, end-face contamination, wavelength pair |
Both LNK lit, heavy packet loss | duplex mismatch, damaged patch lead, distance beyond rated reach |
Link drops as soon as traffic starts | LFP enabled at one end only, or PoE budget exceeded |
Still not sure which model fits your link?
Send the link speed, the fibre you already have (core size and wavelength), the distance and the cabinet temperature to sales@aoatech.com or through the contact page. An engineer will confirm the right part — including whether LFP or 1+1 redundancy is worth paying for in your topology.
Author Bio
Written by the AOA Technology Engineering Team — the engineers who run the link-negotiation and PoE load tests behind these figures. AOA Technology has built fiber optic and industrial networking products in-house since 2008.